Gardena Lawn Mower Art 4005 User Manual

®
GARDENA  
HB 40  
Art. 4005  
MulchCut HB 40 Art. 4010  
D
Gebrauchsanweisung  
Hattrick  
GB Operating Instructions  
Hattrick  
F
Mode d’emploi  
Tondeuse Hattrick  
NL Gebruiksaanwijzing  
Hattrick  
S
I
Bruksanvisning  
Hattrick Gräsklippare  
Istruzioni per l’uso  
Hattrick  
E
P
Manual de instrucciones  
Hattrick  
Instruções de utilização  
Hattrick  
 
35  
 
G
GARDENA Hattrick HB 40  
1. Technical data  
HB 40 / MulchCut HB 40  
Motor  
Power  
Capacity  
petrol engine Briggs & Stratton (Quattro 40)  
2.1 kW  
158 cm3  
Spark plug  
Gap  
Fuel tank capacity  
Fuel  
Champion RC-J-8 / Champion RJ-9LM  
0.75 mm  
1.0 l  
Two-star petrol  
Oil capacity  
Casing  
Cutting width  
Cutting height  
Weight  
approx. 0.6 l (SAE 30 or 10W30)  
plastic  
40 cm  
30-80 mm  
31 kg  
Grass catcher capacity  
Wheels  
Side force  
55 l  
ball bearing  
50 N  
Return force  
Operational safety/gradients  
50 N  
15°  
Working area related emission  
1)  
characteristic value LpA  
81 dB(A)  
2)  
Noise level LWA  
95 dB(A) / 94 dB(A)  
Measuring method according to  
Vibrations at handle avhw  
2.4 ms-2  
EN 836  
directive 2000/14/EC  
1)  
2)  
1)  
2. Information concerning the instructions  
Read these instructions carefully  
and observe the information  
contained in them. Acquaint your- of 16 as well as people, who  
self with the use of the unit, the  
adjustments, its proper use and  
observe the safety instructions.  
For safety reasons,  
children under the age  
Warning! For environ-  
mental and transport  
safety reasons the petrol  
Hattrick lawn mower is supplied  
without motor oil. Therefore,  
the crankcase of the engine  
must be filled with motor oil  
(see 5.1) prior to use, otherwise  
the engine will be damaged.  
A
A
are not acquainted with the  
instructions should not use  
this Hattrick.  
Keep these instructions in  
a safe place.  
3. Proper use  
The GARDENA petrol Hattrick  
lawn mower has been designed  
for cutting lawn and grass areas  
of private houses.  
It is absolutely necessary to  
be used for trimming bushes,  
hedges or shrubs, for cutting  
and pruning of climbers or  
grass on roof or balcony gar-  
dens. Additionally, the Hattrick  
must not be used for chopping  
up branches and twigs and  
for levelling irregularities in the  
soil surface.  
observe the manufacturer’s oper-  
ating instructions to ensure the  
unit’s proper functioning. These  
instructions also contain hints on  
service, maintenance and repair.  
This appliance is for private use  
only and is not designed for use in  
public places, parks, sport arenas,  
street-scapes, in agriculture or  
forestry.  
Attention! For health and  
safety reasons the petrol  
Hattrick lawn mower should not  
A
15  
 
G
G
5.2 Starting the Hattrick  
lawn mower (Fig. F)  
Place your petrol Hattrick lawn  
mower on an even area of the  
lawn.  
After that, the starter handle/cord Do not let the engine run in  
4. Assembly (Fig. A-D)  
closed spaces. There is danger  
of carbon monoxide poisoning.  
(13) must be allowed to return  
slowly.  
4.1 Contents  
The packaging should include  
the following parts:  
petrol and brake bowden cables  
(4/5). Insert the enclosed bolt (8)  
from the outside through the  
bore hole of the top of the guide  
handle (A2).  
4.5 Fixing the bowden cables  
The motor speed can be reduced  
by pushing the throttle (3) towards  
(Fig. C)  
Never start up on a solid sur-  
faced area (e.g. drives, tarred  
surfaces etc.) with the aerator  
roller switched on and a cutting  
height of less than 55 mm as  
the aerator springs can have  
contact with the ground at this  
setting.  
Insert both petrol and brake  
bowden cables into the provided  
bowden cable clip (16) and press  
them onto the bottom part of  
the guide handle (A1).  
.Hattrick HB 40  
the symbol  
(turtle).  
If the engine is cold, press the  
primer (23) several times before  
starting. If the engine is hot there  
is no need to use the primer (23).  
.Grass Catcher (disassembled)  
.Top of guide handle  
.Fastening parts for  
guide handle and throttle  
.Bowden cable clip  
.Spark plug spanner  
.Operating instructions  
.TORX®-wrench  
Release brake lever (10) to switch  
off the engine.  
The bolt (8) is located firmly by  
the square bolt head, into the  
guide handle.  
Make sure that the blades  
and aerator roller (see 6.3)  
can run freely before starting  
the mower. Tilt the mower on  
the rear wheels by pressing on  
the guide handle.  
Press brake lever (10) down to  
the top of the guide handle (A2).  
4.6 Assembly of the  
A
Lift the brake lever (10) and insert grass catcher (Fig. A/D)  
the brake bowden cable (11)  
from the outside into the corre-  
Attention! Be aware that the  
cutting blades take a while  
to stop after turning off the  
engine.  
The grass catcher is supplied  
loose (3 component parts).  
sponding bore hole (12). The cas- The carrying handle (17) is under  
ing of the throttle (9) is now insert- the protective cover (27).  
Push the throttle (3) to the symbol  
(hare) and pull the starter  
handle/cord (13) slightly until the  
ratchet engages. Start the engine  
by quickly pulling out the starter  
handle/cord (13).  
for changing blades  
4.2 Assembly of the  
guide handle (Fig. A)  
ed onto the bolt (8) on the top of  
Unfold the grass catcher (18) and  
the guide handle (A2).  
insert the supporting frame (19)  
Insert washer (7) before fastening  
through the opening of the grass  
the nut (6) (as illustrated).  
Swivel the folded bottom part  
of the guide handle (A1) into the  
working position and allow it to  
engage. Tighten well with the  
lower linkage locking handles (2).  
Put the top of the guide handle  
(A2) onto the bottom part of the  
guide handle (A1) and secure  
using the fastening parts (thread-  
ed bolt; plastic wing nut) (1).  
catcher (18) so that the plastic  
6. Information concerning correct mowing and aerating  
base is at the bottom.  
4.4 How to attach the starter  
Then open the fastening clamps  
handle onto the top of the  
6.1 General remarks  
on the care of lawns  
To keep your lawn well-groomed  
we recommend cutting it regularly no uncut strips are left behind.  
mower in rows as straight as pos- 6.3 Mowing with the  
(20) by hand and fix them onto  
guide handle (Fig. C)  
sible. Ensure that the rows over-  
lap by a few centimetres so that  
aerator cylinder (Fig. H)  
the supporting frame (19).  
By pushing the brake lever (10)  
Fasten the carrying handle (17)  
down, the brake is released from  
by pressing onto the supporting  
the engine. The starter handle  
frame (19).  
Switching the aerator cylinder  
on/off  
Switch off the engine before  
switching the aerator cylinder  
on or off.  
To switch on the aerator cylinder  
set the rotary switch (26) to  
position I.  
once a week. Depending on the  
Guide the Hattrick in walking  
growth of moss and weeds,  
pace only.  
(13) with starter cord (14) can now  
be pulled out of its resting position Note:  
on the petrol motor. Now thread  
switch on the aerator cylinder as  
4.3 Assembly of the throttle  
(Fig. B)  
The throttle (3) is already con-  
nected in working order to the  
The supporting frame (19) is  
the starter cord (14) into the guide shaped to locate the carrying  
required.  
Adjusting the cutting height  
(Fig. G)  
With frequent mowing and aerat-  
ing the lawn becomes healthy  
and strong.  
rings (15) on the top of the guide  
handle (A2).  
handle (17) in the correct  
position.  
The petrol Hattrick lawn mower  
has a central cutting height ad-  
justment knob (24). In front of  
the knob (24) the cutting height  
is displayed (25) increments  
of 5 mm.  
To switch it off set the rotary  
switch (26) to position 0.  
Short clippings (up to a length  
of about 1 cm) can be left on the  
lawn. Longer clippings must be  
removed to prevent the lawn  
becoming yellow or matted.  
5. Initial operation (Fig. E/F)  
Remarks on mowing with the  
aerator cylinder switched on  
Cutting height range 30 - 80 mm The aerator cylinder can be used  
5.1 Preparation for initial  
operation (Fig. E)  
integrated in the oil sealing cap  
(21). The oil level must be bet-  
ween the ADD and FULL mark.  
removed and no petrol may be  
added if the engine is running  
or is hot. If petrol is spilled dur-  
ing filling, the engine must not  
be started until the spilled  
petrol has been wiped up and  
the mower has been removed  
from the area where the fuel  
was spilled. No attempt must  
be made to switch on the igni-  
tion until the petrol vapours  
have dispersed.  
for creating drainage, removing  
matting and moss in the lawn  
as well as for cutting flat-rooting  
weeds.  
Cut and aerate the lawn for the  
first time in spring when the grass When working on slopes, al-  
begins to grow and can be walked ways mow at right angles to  
Note:  
For environmental and  
transport safety reasons  
A
Always check the oil level  
before mowing.  
the petrol Hattrick lawn mower  
is supplied without motor oil.  
Therefore, the crankcase of  
the engine must be filled with  
0.6 l motor oil (SAE 30 or  
10W30).  
on. If the grass has grown too  
long, first cut it lengthwise with  
a high cutting setting (without  
switching on the aerator cylinder)  
and then cut at right angles with  
the desired cutting setting, with  
the aerator cylinder (optional)  
switched on.  
the slope. To prevent the petrol  
Hattrick lawn mower from slid-  
ing way, point it slightly uphill.  
The recommended fuel is  
unleaded two-stroke petrol.  
If the grass is particularly long  
due to infrequent lawn care (e.g.  
after holidays), disengage the  
aerator cylinder, and pre-cut with  
the maximum cutting height  
to prevent overload of the lawn  
mower.  
Take extra care when changing  
direction on slopes.  
Warning! Fuel is highly  
inflammable. Fuel must  
be stored only in containers  
A
Unscrew the oil sealing cap (21)  
and fill with 0.6 l of SAE 30 quality authorised for the purpose.  
oil.  
The oil level can be checked  
(when engine is switched off)  
by means of the oil dip stick (22)  
For safety reasons, slopes  
with a gradient of more than  
15° must not be mowed.  
To safeguard against fire,  
keep grass, leaves, grease and  
oil away from engine and ex-  
haust.  
The fuel must be filled only  
outdoors; do not smoke during  
filling. Fill with petrol prior to  
use; the petrol cap must not be  
At the end of the cutting row  
or for turning around, tilt the  
mower on the rear wheels by  
pressing on the guide handle.  
This way you can turn it easily  
with the aerator cylinder run-  
6.2 Mowing (Fig. G-I)  
Always keep the under side of  
the mower casing clean and  
remove grass deposits. De-  
posits complicate the start-up  
procedure and affect the cut-  
Cut only with sharp blades so  
that the grass does not fray and  
the lawn does not turn yellow.  
To obtain a clean cutting result  
guide the petrol Hattrick lawn  
ting result as well as discharge ning free.  
of grass clippings.  
16  
17  
 
G
G
After having aerated heavily  
moss-covered areas, it is re-  
commended to resow the lawn.  
This will help the affected lawn  
to recover quickly.  
The aerator cylinder use is  
optional depending on the needs  
and condition of the lawn.  
The table below provides infor-  
mation on the use of the aerator  
cylinder.  
Follow the manufacturer’s  
instructions when replacing  
the blades, blade bar and for  
aerator cylinder.  
4. Reverse the blades (30) or  
mount new blades (30) and  
secure tightly (torque 25 Nm).  
(During installation make sure  
that the ratchet toothed locking  
washers (31) are fitted under  
the nuts (28) and that the nuts  
(28) are on the top of the blade  
bar (32).)  
tank lid is properly closed.  
Tilt the lawn mower to the  
tank-located side; keep spark  
plugs and sound absorber of  
the motor upwards.  
7.2 How to replace the blades,  
blade bar and the aerator  
cylinder (Fig. K-M)  
Please use only the Original  
GARDENA Spare Blades:  
3. Release screws (39) with  
an appropriate Phillips head  
screwdriver.  
4. Remove the bearing sheet  
steel (40).  
5. Remove aerator cylinder (38)  
together with end plate (41)  
of the drive shaft (42) (square)  
by tilting and pulling out.  
6. Place new aerator cylinder (38)  
onto drive shaft (42) (square);  
stick on end plate (41) and  
tighten with the bearing sheet  
steel (40) in the casing.  
Use of the aerator cylinder  
Cutting height setting  
Function of the aerator cylinder  
Deep aeration of the soil  
30 - 35 mm  
The aerator springs penetrate up to 7 mm  
deep depending on the type of soil.  
Replacing the blade bar  
(Fig. L)  
Triangular blades  
(HB 40)  
Aeration of the soil surface  
35 - 40 mm  
The aerator springs remove moss,  
matting, and weeds rooting near the  
surface.  
Art. No. 4098 Damaged blade bars must be  
Rectangular Blades  
(MulchCut HB 40) Art. No. 4099  
Aerator cylinder Art. No. 4097  
replaced to prevent imbalance.  
1. Remove the spark plug in  
order to avoid risk of injury  
if the engine accidentally  
is started.  
Combing the lawn  
40 - 45 mm  
40 - 55 mm  
The aerator springs remove residues from  
the lawn.  
You can order these spare parts  
from your GARDENA dealer  
or directly from the GARDENA  
customer service.  
Gathering grass clippings etc.  
The aerator springs remove even wet or  
trodden-in grass clippings etc. from the  
lawn.  
2.  
Empty the tank or run  
the mower until the  
tank is empty! Make sure the 7.3 Engine maintenance  
A
Never use spare parts or ac-  
cessories which have not been  
designed by the manufacturer!  
tank lid is properly closed.  
Changing oil (Fig.E)  
Tilt the lawn mower to the  
Always change the oil when  
tank-located side; keep spark  
the engine is hot and the tank  
plugs and sound absorber of  
is empty and closed.  
6.4 Mowing with the  
grass catcher (Fig. I)  
As soon as there are grass clip-  
pings left on the lawn during  
mowing and aerating, the grass  
catcher should be emptied.  
be difficult to start. Pull the petrol  
Hattrick lawn mower back about  
1 m so that the grass clippings  
drop out easily.  
Afterwards, the grass catcher  
should be emptied.  
the carrying handle (17) and in-  
sert into the the discharge open-  
ing from above.  
Replacing the blades (Fig. K)  
the motor upwards.  
Note:  
Note:  
3. Release the hexagon head  
bolt (33) with an appropriate  
wrench (SW 13) and remove  
the blade bar (32) from the  
drive shaft.  
4. Insert new blade bar and  
tightly screw with the following  
washers (in the same order):  
a) fibre washer (34)  
Carry out the first motor oil  
If properly seated the protec-  
tive cover (27) fits snugly to  
the grass catcher (18).  
The blade has two cutting  
edges. If one edge has become  
blunt the blade can be re-  
versed. Broken blades must be  
replaced immediately as it can  
cause an imbalance problem.  
change after 5 hours of operation,  
then every 50 hours of operation  
or once a year at the end of the  
mowing season, depending on  
which comes first.  
In order to do this, open oil seal-  
ing cap (21), tilt the mower so  
that the old oil can flow into an  
oil-trough. Dispose of waste oil  
according to local regulations.  
To remove the grass catcher (18)  
lift the protective cover (27) on  
your petrol Hattrick lawn mower  
with one hand. With the other  
hand hold the grass catcher (18)  
by the carrying handle (17) and  
remove the grass catcher (18)  
upwards.  
Note:  
To ensure good collection, re-  
gularly clean the grass catcher  
inside and outside.  
Mowing without  
the grass catcher  
The protective cover (27) is  
mounted in such a way that the  
petrol Hattrick lawn mower can  
be used without the grass catcher  
with the protective cover (27)  
closed. The clippings are ejected  
onto the lawn below the protec-  
tive cover (27).  
Do not regrind the blades, it  
will cause imbalance.  
Attaching the grass catcher  
Attach the grass catcher  
b) strain washer (35)  
The blades must always be  
replaced or reversed in pairs.  
c) small steel washer (36)  
and with the hexagon head  
bolt (33) (Torque: 40 Nm).  
A
only with the engine  
switched off and the cutting  
blade at a stand still.  
If the protective cover (27) is re-  
leased, it automatically shuts and  
covers the discharge opening.  
Position the mower on a level  
surface again and fill it with motor  
oil (0.6 l SAE 30 or 10W30)  
(see 5.1).  
When replacing the blades  
always use the new nuts and  
bolts supplied with the spare  
blades.  
Be sure that strain washer (35)  
has been installed in the cor-  
rect position (see fig. L1).  
Lift the protective cover (27) with  
one hand. With the other hand  
hold the grass catcher (18) by  
If grass clippings stick in the dis-  
charge opening, the mower may  
Checking and cleaning  
1. Remove the spark plug in  
order to avoid risk of injury  
if the engine is accidentally  
started.  
Replacing the aerator cylinder  
(Fig. M)  
The aerator cylinder is subject  
to natural wear and tear. If the  
springs (37) are worn it will not  
function correctly.  
the spark plug  
Clean a contaminated spark plug  
with a brass wire brush and rag.  
Check the electrode gap (setting:  
0.75 mm gap). Replace a badly  
worn or damaged plug.  
7. Maintenance, service, storage  
2.  
Empty the tank or run  
the mower until the  
tank is empty! Make sure the The aerator cylinder (38) must  
tank lid is properly closed.  
Tilt the lawn mower to the  
tank-located side; keep spark  
plugs and sound absorber of  
the motor upwards.  
7.1 Maintenance  
Repairs may only be carried  
For security reasons, replace  
the tank lid if damaged.  
A
Maintenance includes all jobs  
which keep your petrol Hattrick  
lawn mower in perfect working  
order. By regularly checking the  
unit (firm seating of screw con-  
nections, cracks, damage) and  
replacing defective or worn parts  
you can prevent accidents and  
failure.  
out by GARDENA service  
centres or dealers authorised  
by GARDENA.  
Cleaning the air filter (Fig. N)  
Cleaning the air filter is ne-  
cessary every 3 months or after  
25 hours of operation. In ex-  
treme dusty conditions do so  
more frequently.  
Never clean your petrol Hattrick  
lawn mower with running water,  
in particular with water under  
high pressure.  
be replaced.  
1. Remove the spark plug in  
order to avoid risk of injury  
if the engine is accidentally  
started.  
Attention: Always detach  
the spark plug before  
working on your petrol Hattrick Store your petrol Hattrick lawn  
lawn mower (for checking and  
maintenance) to prevent risk  
of injury!  
A
3. Hold the locking nuts (28) at  
the back and unscrew the bolts  
(29), using the TORX®-wrench  
provided.  
mower in a dry place where  
it is protected from frost. The  
lawn mower should be stored  
out of the reach of children.  
2.  
Empty the tank or run  
the mower until the  
tank is empty! Make sure the  
Remove screw (43).  
Fully remove air filter by pulling  
sideways and/or from the front.  
A
18  
19  
 
G
G
Make sure that no foreign  
substances fall into the car-  
burettor. Afterwards pull  
cover (44) upwards. Completely  
disassemble the air filter (45)  
and clean all parts.  
Hattrick lawn mower on its side  
opposite the tank and clean it  
with a brush or rag.  
Unscrew the spark plug and  
Problem  
Possible cause  
Remedy  
pour 1 tablespoon of motor oil  
into the cylinder. Turn the motor  
by slowly pulling on the starter  
handle/cord so that the oil is  
distributed. Screw in the spark  
plug again.  
Uneven running.  
Strong vibration of the unit.  
Blade bar or blades damaged  
(imbalance).  
Blade bar fastening on motor  
shaft is loose.  
Replace damaged parts.  
Tighten the blade or blade bar  
bolts.  
7.5 Storage (Fig. A)  
Let the engine cool down be-  
fore storing the petrol Hattrick  
lawn mower in a closed room.  
Cleaning the foam element.  
Clean foam element in liquid  
detergent and water. The foam  
element should be replaced if  
it is extremely dirty or damaged.  
Engine does not start.  
Primer has not been operated  
before starting.  
Press primer several times  
(see 5.2).  
After having thoroughly removed  
dirt and remaining grass we re-  
commend you to clean the petrol  
Never store the petrol Hattrick  
lawn mower with fuel in the  
Spark plug defective or  
tank empty.  
Clean and replace spark plug,  
fill fuel tank.  
tank where petrol vapour could Hattrick lawn mower with mainte-  
come into contact with an  
open flame or could be ignited.  
nance spray.  
After cleaning press dry the  
foam element with a clean rag.  
Re-moisten the foam element  
with oil.  
Engine runs for a short time  
but then suddenly stops  
with a loud bang.  
No motor oil in crankcase.  
Piston and crankshaft bearings  
have jammed.  
Engine overhaul by a Service  
Centre.  
If you have any problem with  
your petrol Hattrick lawn mower,  
please contact our Customer  
Service or return the defective  
Always store your petrol Hattrick  
lawn mower in a closed dry place.  
Aerator cylinder does not run.  
Rotary switch is in “0” position.  
V-belt defective.  
Set rotary switch to “Iposition.  
Re-assemble all parts in reverse  
order and secure with screw (43)  
onto carburettor.  
To save space the handle can  
be folded down. Loosen the lower unit together with a short descrip-  
locking handles (2) and pull the  
bars sideways out of the mount.  
Loosen plastic wing nut (1) at the  
joint. Fold guide handle down in  
a Z-shape.  
Replace V-belt. Contact  
GARDENA service station.  
tion of the problem and, in case  
of guarantee, with a copy of the  
receipt to one of the GARDENA  
service centres listed on the rear  
page.  
Cleaning the cooling air  
passages  
Clean grass from cooling fins  
and air passages.  
Lawn turns to yellow.  
Not a clean cut.  
Blades are too blunt.  
Replace or reverse the blades.  
Correct cutting height.  
Cutting height is too low.  
We expressly point out that,  
in accordance with the product  
liability law, we are not liable  
for any damage caused by our  
units if it is due to improper  
repair or if parts exchanged are  
not original GARDENA parts  
or parts approved by us, and  
if the repairs were not carried  
out by a GARDENA Service  
Centre or an authorised spe-  
cialist. The same applies to  
spare parts and accessories.  
If any other faults occur, please contact GARDENA Service.  
Service interval  
When folding down the  
bars make sure that the  
gas and brake bowden cables  
are not jammed or damaged.  
In order to achieve trouble-free  
operation of the engine, this lawn  
mower should be checked every  
2 to 3 years by a GARDENA  
Service Centre or a dealer  
authorised by GARDENA.  
A
9. Advice for proper use / safety instructions  
Checks before each  
operation  
You are responsible for the  
safety of the working area.  
If, in spite of care, there is an  
obstruction when cutting, turn  
off the petrol Hattrick lawn  
mower and remove it. Check  
the unit for damage and have  
it repaired if necessary.  
Wintering  
A
If the engine is shut down for  
more than 30 days, firstly empty  
the tank. Afterwards, let the  
engine run until it runs out of  
petrol.  
Inspect the unit before each  
use. Do not use the petrol  
Hattrick lawn mower if safety  
devices (safety handle; safety  
cover) and/or the blade bar  
or the blades are damaged or  
worn. Never operate the unit  
with the safety devices by-  
passed or missing.  
Only use the petrol Hattrick  
lawn mower for the purposes  
specified in these instructions.  
7.4 Service  
Residual dirt and grass can be  
most easily removed immediately  
after mowing. Place the petrol  
Only work when visibility is  
good.  
A
Interruption to work  
Familiarise yourself with the  
surroundings of your working  
area. Check for possible risks  
Never leave the petrol Hattrick  
lawn mower to run unattended.  
8. Trouble-shooting  
which might be not audible due If your work is interrupted,  
The following table contains the  
problems most frequently occur-  
ring and shows how to remedy  
them.  
For safety, please contact  
one of the GARDENA service  
centres or an authorised  
specialist for any other pro-  
blem.  
Inspect the area to be cut  
before beginning work.  
Remove any foreign objects  
(e.g. stones) from the area.  
Check the working area for  
foreign objects (e.g. stones)  
while working.  
to the noise of the machine.  
store the unit in a safe place.  
Remove the spark plug!  
Wear non-slip shoes and long  
trousers to protect your legs.  
When changing to another  
working area, switch off the  
petrol Hattrick lawn mower.  
Keep fingers and feet away  
from the cutting blades and  
the aerator cylinder.  
Problem  
Possible cause  
Remedy  
The blade bar and the blades  
must be checked regularly  
for damage and properly re-  
paired if necessary.  
A
Check local regulations  
Abnormal noise.  
Clattering in the unit.  
Motor fixing screws or  
mower casing loose.  
Tighten screws.  
Make sure that there are no  
other people (especially chil-  
dren) or animals anywhere  
near the working area.  
Never use the unit when it is  
raining or in damp or wet areas.  
Whistling noise.  
Foreign body blocking  
aerator cylinder.  
Switch off aerator cylinder,  
remove the spark plug, remove  
foreign body.  
Do not use the petrol Hattrick  
lawn mower in or near swim-  
ming pools or ponds.  
Proper use /  
Ensure that you have a secure  
foothold when working.  
Attention! Take extra care  
when walking backwards.  
You may stumble!  
A
responsibility  
V-belt slipping.  
Contact GARDENA Service  
Centre.  
Lawn mowers can cause  
serious injuries!  
Please observe the local re-  
gulations regarding quiet times.  
20  
21  
 
G
EU Certificate of Conformity  
The undersigned  
GARDENA Kress + Kastner GmbH · Hans-Lorenser-Str. 40 · D-89079 Ulm  
hereby certifies that, when leaving our factory, the units indicated below are in accordance with the  
harmonised EU guidelines, EU standards of safety and product specific standards.  
This certificate becomes void if the units are modified without our approval.  
Description of the units:  
Hattrick  
Harmonised European  
standards:  
EN 292-1  
EN 292-2  
EN 836  
Ulm, 08.02.2002  
Types:  
HB 40 / MulchCut HB 40  
Thomas Heinl  
Technical Director  
Art. No.:  
4005 / 4010  
Noise level:  
measured / guaranteed  
95 / 96 dB(A)  
EU directives:  
HB 40  
Machinery Directive 98/37/EC  
Electromagnetic Compatibility  
89/336/EC  
Directive 93/68/EC  
Directive 2000/14/EC  
MulchCut HB 40 94 / 96 dB(A)  
Year of CE marking:  
1996 (HB 40)  
1998 (MulchCut HB 40)  
22  
 
the unit or repair it free of charge  
if the following conditions apply:  
.The unit must have been  
handled properly and in keep-  
ing with the requirements of  
the operating instructions.  
.Neither the purchaser or a  
non-authorised third party have  
attempted to repair the unit.  
Une intervention sous garantie  
ne prolonge pas la durée initiale  
de la garantie contractuelle.  
D
Garantie  
GARDENA gewährt für dieses  
Produkt die gesetzliche Garantie  
(ab Kaufdatum). Abweichend  
davon werden für das Kunststoff-  
gehäuse 10 Jahre Garantie ge-  
währt. Diese Garantieleistung  
bezieht sich auf alle wesentlichen  
Mängel des Gerätes, die nach-  
weislich auf Material- oder Fabri-  
kationsfehler zurückzuführen  
sind. Sie erfolgt durch die Ersatz-  
lieferung eines einwandfreien  
Gerätes oder durch die kosten-  
lose Reparatur des eingesandten  
Gerätes nach unserer Wahl,  
wenn folgende Voraussetzungen  
gewährleistet sind:  
Toutes les revendications dé-  
passant le contenu de ce texte  
ne sont pas couvertes par la  
garantie, quel que soit le motif  
de droit.  
Pendant la période de garantie,  
le Service Après-Vente et les  
Centres SAV agréés effectue-  
ront, à titre payant, les répara-  
tions nécessaires par suite de  
manipulations erronées.  
The triangular blades (Hattrick)/  
rectangular blades (MulchCut)  
and the aerator cylinder are wear-  
ing parts and are not covered  
by the guarantee.  
This manufacturer’s guarantee  
does not affect the user’s exist-  
ing warranty claims against the  
dealer/seller.  
En cas de réclamation, veuillez  
envoyer le produit en port payé  
avec le bon d’achat et une de-  
scription du problème, à l’adresse  
du Service Après-Vente figurant  
In case of claim, please return  
the faulty unit together with a copy au verso.  
of the receipt and a description  
of the fault, with postage paid to  
one of the GARDENA Service  
Centres listed on the back of  
these operating instructions.  
.Das Gerät wurde sachgemäß  
und laut den Empfehlungen  
in der Gebrauchsanweisung  
behandelt.  
.Es wurde weder vom Käufer  
noch von einem Dritten ver-  
sucht, das Gerät zu reparieren.  
N
Garantie  
GARDENA geeft op dit product  
de wettelijke garantie (vanaf de  
aankoopdatum). Op het kunststof  
maaihuis is echter een garantie  
van 10 jaar van toepassing. Deze  
garantie heeft betrekking op alle  
wezenlijke defecten aan het toe-  
stel, die aanwijsbaar op mate-  
riaal- of fabricagefouten berusten.  
Garantie vindt plaats door de le-  
vering van een vervangend appa-  
raat of door de gratis reparatie  
van het ingestuurde apparaat,  
naar onze keuze, indien aan de  
volgende voorwaarden is voldaan:  
.Het apparaat werd vakkundig  
en volgens de adviezen in de  
gebruiksaanwijzing behandeld.  
.Noch de koper, noch een  
Die Verschleißteile Dreieckmes-  
ser (Hattrick) / Rechteckmesser  
(MulchCut) und Lüfterwalze sind  
von der Garantie ausgeschlossen.  
F
Garantie  
GARDENA accorde pour cet ap-  
pareil la garantie légale à comp-  
ter du jour de l’achat. Le carter  
en polypropylène est, lui, garanti  
10 ans. La garantie est assurée  
par le remplacement gratuit des  
pièces défectueuses ou de l’ap-  
pareil. Le choix en étant laissé  
à la libre initiative de GARDENA.  
En tout état de cause s’applique  
la garantie légale couvrant toutes  
les conséquences des défauts  
ou vices cachés (article 1641 et  
suivants du Code Civil).  
Diese Hersteller-Garantie berührt  
die gegenüber dem Händler/  
Verkäufer bestehenden Gewähr-  
leistungsansprüche nicht.  
Im Reklamationsfall schicken Sie  
bitte das defekte Gerät zusam-  
men mit einer Kopie des Kauf-  
belegs und einer Fehlerbeschrei-  
bung frankiert an die auf der  
Rückseite angegebene Service-  
adresse.  
Pour que ces garanties soient  
valables, les conditions suivantes  
doivent être remplies :  
.Lappareil a été manipulé de  
manière adéquate, suivant les  
instructions du mode d’emploi.  
.Il n’y a eu aucun essai de  
réparation, ni par le client, ni  
par un tiers.  
derde persoon heeft getracht  
het apparaat te repareren.  
G
Guarantee  
De aan slijtage onderhevige  
driehoeksmessen (Hattrick) /  
rechthoeksmessen (Hattrick-  
mulchmaaier) en de verticuteer-  
rol vallen niet onder de garantie.  
GARDENA honours the guaran-  
tee legally required for this pro-  
duct (starting from the date of  
purchase). As an exception, we  
guarantee the plastic casing for  
10 years. This guarantee covers  
all serious defects of the unit  
that can be proved to be material  
or manufacturing faults. Under  
warranty we will either replace  
Deze garantie van de producent  
heeft geen betrekking op de ten  
aanzien van de handelaar/ver-  
koper bestaande aansprakelijk-  
heid.  
Les lames triangulaires (Hattrick)  
/ lames rectangulaires (MulchCut)  
et le rouleau d’aération sont des  
pièces d’usure et sont par con-  
séquent exclues de la garantie.  
71  
 
Deutschland  
GARDENA Kress + Kastner GmbH  
GARDENA Service  
Hans-Lorenser-Straße 40  
D-89079 Ulm  
Produktfragen: (0731) 490-123  
Reparaturen: (0731) 490-290  
Finland  
Norway  
Habitec Oy  
GARDENA Norge A/S  
Postboks 214  
2013 Skjetten  
Martinkyläntie 52  
01720 Vantaa  
France  
Poland  
GARDENA France  
Service Après-Vente  
BP 50080  
GARDENA Polska Sp. z o.o.  
Szymanów 9 d  
Argentina  
05-532 Baniocha  
Argensem S.A.  
95948 ROISSY CDG Cedex  
Portugal  
Venezuela 1075  
Great Britain  
MARKT (Portugal), Lda.  
Recta da Granja do Marquês  
Edif. GARDENA  
(1618) El Talar - Buenos Aires  
GARDENA UK Ltd.  
27-28 Brenkley Way  
Blezard Business Park  
Seaton Burn  
Australia  
NYLEX Corporation Ltd.  
25-29 Nepean Highway  
P.O. Box 68  
Algueirão  
2725-596 Mem Martins  
Newcastle upon Tyne  
NE13 6DS  
Russia / Россия  
АО АМИДА ТТЦ  
Mentone, Victoria 3194  
Austria  
Greece  
ул. Моcфилмовcкая 66  
117330 Моcква  
GARDENA Österreich Ges. m.b.H.  
Stettnerweg 11-15  
2100 Korneuburg  
Agrokip G. Psomadopoulos & Co.  
20, Lykourgou str.  
Kallithea - Athens  
Singapore  
Variware  
Holland Road Shopping Centre  
227-A 1st Fl., Unit 29  
Holland Avenue  
Singapore 1027  
Belgium  
Hungary  
MARKT (Belgium) NV/SA  
Sterrebeekstraat 163  
1930 Zaventem  
GARDENA Magyarország Kft.  
Késmárk utca 22  
1158 Budapest  
Brazil  
Iceland  
Heimilistaeki hf  
Saetun 8  
P.O. Box 5340  
125 Reykjavik  
Slowenia / Croatia  
Silk d.o.o. Trgovina  
Brodišče 15  
M. Cassab  
Av. das Nações Unidas, 20.882  
Santo Amaro, CEP 04795-000  
São Paulo - S.P.  
1236 Trzin  
South Africa  
Bulgaria / България  
ДЕНЕКС ООД  
бул. „Черни връх“ 43  
София 1407  
Republic of Ireland  
Michael McLoughlin & Sons  
Hardware Limited  
Long Mile Road  
GARDENA South Africa (Pty.) Ltd.  
P.O. Box 11534  
Vorna Valley 1686  
Spain  
Dublin 12  
Canada  
ANMI Andreu y Miriam S.A.  
Calle Pere IV, 111  
08018 Barcelona  
GARDENA Canada Ltd.  
100, Summerlea Road  
Brampton, Ontario  
Canada L6T 4X3  
Italy  
GARDENA Italia S.r.l.  
Via Donizetti 22  
20020 Lainate (Mi)  
Sweden  
GARDENA Svenska AB  
Box 9003  
Chile  
Japan  
Antonio Martinic Y CIA. LTDA.  
Gilberto Fuenzalida 185 Loc.  
Las Condes - Santiago de Chile  
KAKUDAI Mfg. Co. Ltd.  
1-4-4, Itachibori Nishi-ku  
Osaka 550  
20039 Malmö  
Switzerland  
GARDENA Kress + Kastner AG  
Bitziberg 1  
Costa Rica  
Luxembourg  
Magasins Jules Neuberg  
Grand Rue 30  
Case Postale No. 12  
Luxembourg 2010  
Compania Exim  
Euroiberoamericana S.A.  
350 Sur del Automercado  
Los Yoses  
8184 Bachenbülach  
Ukraine / Украина  
АОЗТ АЛЬЦЕСТ  
ул. Гайдара 50  
г. Киев 01033  
San Pedro  
Netherlands  
Cyprus  
GARDENA Nederland B.V.  
Postbus 50176  
Turkey  
FARMOKIPIKI LTD  
P.O. Box 7098  
74, Digeni Akrita Ave.  
1641 Nicosia  
Dost Diþ Ticaret Mümessillik A.Þ.  
Yeþilbaðlar Mah. Baþkent  
Cad. No. 26  
Pendik - Ýstanbul  
USA  
GARDENA  
1305 AD ALMERE  
Neth. Antilles  
Jonka Enterprises N.V.  
Sta. Rosa Weg 196  
P.O. Box 8200  
Czech Republic  
GARDENA spol. s.r.o.  
Řípská 20  
Curaçao  
3085 Shawnee Drive  
Winchester, VA 22604  
62700 Brno  
New Zealand  
NYLEX New Zealand Limited  
Private Bag 94001  
South Auckland Mail Centre  
10 Offenhauser Drive  
East Tamaki, Manukau  
Denmark  
GARDENA Danmark A/S  
Naverland 8  
4005-20.960.07/0021  
GARDENA Kress + Kastner GmbH  
Postfach 27 47, D-89070 Ulm  
http://www.gardena.com  
2600 Glostrup  
76  
 

Electro Voice Microphone RE1000 User Manual
Extreme Networks Switch 12802 User Manual
Fender Speaker System VM 212 User Manual
Fisher Price Indoor Furnishings 79514 User Manual
Frigidaire Yard Vacuum FRS18PYS2 User Manual
Frymaster Fryer 47 Series User Manual
GE Microwave Oven JEM31 User Manual
GE Microwave Oven ZEM115 User Manual
GE Oven JKP35SM User Manual
Gigabyte Network Card GN WB01GS User Manual